Network Bridging

Bridged networking can be used to configure your Virtual Machines. Some tweaking is necessary to make the network configuration work on our network.

Lines highlighted in yellow in the configuration examples keywords in capital letters that you must change for your own values. For example; IP_FAIL_OVER which you must change for your failover IP.

DEFAULT_SERVER_IP:
  The primary IP of your dedicated server.
IP_FAIL_OVER: The Failover IP you want to configure
GATEWAY_VM: Your server IP with the last octet replaced by 254

Requirements

  • A dedicated server with an hypervisor installed (Ex: VMware ESXi, Citrix Xen Server, Proxmox, etc.)
  • Have assigned a mac to a virtual IP FailOver
  • Knowledge about SSH
To configure Virtual Machines, you need to know the gateway of your host machine (nsxxx.netksxxx.net ...). To do this, you must replace the last octet of the IP address assigned to your server with .254.

For example:

  • IP of your server : 123.456.789.012
  • Gateway’s IP is your server’s main IP ending in .254
  • So the gateway’s IP is: 123.456.789.254

Applying the configuration

Warning

The gateway you need to use in your virtual machine should not be, The IP of your dedicated server or IP failover but you must use the gateway provides for your dedicated server. You must in no case use:

route add default gw dev eth0

Otherwise you may cut your IP for the virtual server. To determine the correct gateway to use:

  • IP failover is: YYY.YYY.YYY.YYY
  • Main IP of your dedicated server: XXX.XXX.XXX.XXX
  • So the IP of the gateway for your virtual machine (GATEWAY_VM) : **XXX.XXX.XXX**.254

This gateway will be referred as GATEWAY_VM later in the guide.

Debian & derivatives (Ubuntu, CrunchBang, SteamOS...)

File: /etc/network/interfaces

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
auto lo eth0
iface lo inet loopback
iface eth0 inet static
    address IP.FAIL.OVER
    netmask 255.255.255.255
    broadcast IP.FAIL.OVER
    post-up route add GATEWAY_VM dev eth0
    post-up route add default gw GATEWAY_VM
    pre-down route del GATEWAY_VM dev eth0
    pre-down route del default gw GATEWAY_VM

File: /etc/resolv.conf

1
nameserver 213.186.33.99 #  DNS Server

Note

For Debian 6, dns server configuration is done directly in the file /etc/network/interfaces where you have to find this section:

# dns-* options are implemented by the resolvconf package, if installed (default)
dns-nameservers 213.186.33.99 # DNS Server

 

Redhat & derivatives (CentOS, Scientific Linux, ClearOS...)

File: /etc/sysconfig/network-scripts/ifcfg-eth0

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
DEVICE=eth0
BOOTPROTO=none
ONBOOT=yes
USERCTL=no
IPV6INIT=no
PEERDNS=yes
TYPE=Ethernet
NETMASK=255.255.255.255
IPADDR=IP.FAIL.OVER
GATEWAY=GATEWAY_VM
ARP=yes
HWADDR=MY:VI:RT:UA:LM:AC

File : /etc/sysconfig/network-scripts/route-eth0

1
2
GATEWAY_VM dev eth0
default via GATEWAY_VM dev eth0

File : /etc/resolv.conf

1
nameserver 213.186.33.99 # DNS Server

For OpenSUSE, NETWORK_GW_VM= Network of the GATEWAY_VM which is the main IP of your server where you replace the last octet by 0.

If the file ifcfg-ens32 does not exist, you’ll have to create it.

File : /etc/sysconfig/network/ifcfg-ens32

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
DEVICE=ens32
BOOTPROTO=static
ONBOOT=yes
ARP=yes
USERCTL=no
IPV6INIT=no
TYPE=Ethernet
STARTMODE=auto
IPADDR=IP.FAIL.OVER
NETMASK=255.255.255.255
GATEWAY=GATEWAY_VM
HWADDR=MY:VI:RT:UA:LM:AC

If the file ifroute-ens32 does not exist, you’ll have to create it.

File : /etc/sysconfig/network/ifroute-ens32

1
2
3
GATEWAY_VM - 255.255.255.255 ens32
NETWORK_GW_VM - 255.255.255.0 ens32
default GATEWAY_VM

In /etc/sysconfig/network/config, you need to have:

1
NETCONFIG_DNS_STATIC_SERVERS=”213.186.33.99”

FreeBSD 8.0

File : /etc/rc.conf

1
2
3
4
ifconfig_em0="inet IP.FAIL.OVER netmask 255.255.255.255 broadcast IP.FAIL.OVER"
static_routes="net1 net2"
route_net1="-net GATEWAY_VM/32 IP.FAIL.OVER"
route_net2="default GATEWAY_VM"

File : /etc/resolv.conf

1
nameserver 213.186.33.99 # DNS Server

Windows 2003

First, open the “Network Connections” panel (Start -> Control Panel -> Network Connections -> Local Area Connections)

Then, select Properties :

Local Area Connections

Then, select Internet Protocol (TCP/IP):
Finally, you will need your ip Failover in the field “IP Address”,
the subnet mask 
255.255.0.0, the gateway to your physical machine as default gateway and ip 213.186.33.99 as the preferred DNS server.

For the second step, via the Start menu, click Run, then type regedit. Once in the application, you should find your ip-failover (Edit -> Search). Once the IP found, double-click the parameter SubnetMask? “and change 255.255.0.0 to 255.255.255.255, then you validate.

Close the registry editor

Finally, to validate the changes, you must restart the network interface (Start -> Control Panel -> Network Connections -> Connection LAN -> right click, then Disable)

Wait a few seconds and re-enable the network connection.

Other distributions

Here is the network configuration required in the Virtual Machine:

  • ipIP_FAIL_OVER
  • netmask255.255.255.255

It is also required to add a default gateway to the Virtual Machine:
You will then need to configure the DNS of your machine so that it can make domain resolution. The IP of the DNS server is 213.186.33.99

Cette réponse était-elle pertinente?

0 Utilisateurs l'ont trouvée utile